tx should work, but fifo isn't transmitted

git-svn-id: https://svn.spreadspace.org/mur.sat@431 7de4ea59-55d0-425e-a1af-a3118ea81d4c

1 files changed, 49 insertions, 30 deletions

diff --git a/software/hhd70dongle/c1101lib.c b/software/hhd70dongle/c1101lib.c
index 60a3b4d..7958309 100644
--- a/software/hhd70dongle/c1101lib.c
+++ b/software/hhd70dongle/c1101lib.c
@@ -62,6 +62,8 @@ int16_t spi_c1101_write_byte_ok_get_status(char data)
     return sb;
 }
 
+#define spi_c1101_strobe_command spi_c1101_write_byte_ok_get_status
+
 // note addresses range from 0x00 to 0x2F for normal registers and 0xF0 to 0xFD for special status registers
 int16_t spi_c1101_read_register(char address)
 {
@@ -94,14 +96,6 @@ int16_t spi_c1101_write_register(char address, char byte)
     return 1;
 }
 
-// note addresses range from 0x30 to 0x3D for command strobes
-int16_t spi_c1101_strobe_command(char address)
-{
-    if (spi_c1101_write_byte_ok_get_status(address) < 0)
-        return -1;
-    return 1;
-}
-
 void spi_c1101_dump_registers_to_usb(void)
 {
     int c = 0;
@@ -130,7 +124,7 @@ int spi_c1101_read_rxfifo(int leave_num_bytes, char *buffer, int maxlen)
     sb = spi_c1101_write_byte_ok_get_status(SPIC1101_ADDR_FIFO_READ_BURST);
     if (sb < 0)
         return -1;
-    num_fifo_available = SPIC1101_SB_FIFO_BYTES_AVAILABLE((char)sb);
+    num_fifo_available = SPIC1101_SB_FIFO_BYTES_AVAILABLE(sb);
     //note if num_fifo_available  == 15 then 15 or more bytes are available
     //FIXTHIS
     while (maxlen-- && num_fifo_available - num_read <= leave_num_bytes)
@@ -143,26 +137,22 @@ int spi_c1101_read_rxfifo(int leave_num_bytes, char *buffer, int maxlen)
 }
 
 //note: always check if num_written returned == len given
-//note: currently this function writes at most 15 bytes
 int spi_c1101_write_txfifo(char *buffer, int len)
 {
     char sb;
     int num_written = 0;
-    int num_fifo_available = 0;
     spi_cs_enable();
     spi_c1101_wait_chip_rdy();
     sb = spi_c1101_write_byte_ok_get_status(SPIC1101_ADDR_FIFO_WRITE_BURST);
     if (sb < 0)
         return -1;
-    num_fifo_available = SPIC1101_SB_FIFO_BYTES_AVAILABLE((char)sb);
-    //note if num_fifo_available  == 15 then 15 or more bytes are available
-    //FIXTHIS
-    if (num_fifo_available < len)
-        len = num_fifo_available;
-    while (len--)
+    uint8_t debug_sb[6];
+    while (len-- > 0 && SPIC1101_SB_FIFO_BYTES_AVAILABLE(sb) > 2)
     {
-        //hope this works !!
-        spi_write_byte(buffer[num_written++]);
+        usb_rawhid_send((uint8_t*)"TXFifo bytes available",255);
+        debug_sprint_int16hex(debug_sb, SPIC1101_SB_FIFO_BYTES_AVAILABLE(sb));
+        usb_rawhid_send(debug_sb,255);
+        sb = spi_c1101_write_byte_ok_get_status(buffer[num_written++]);
     }
     spi_cs_disable();
     return num_written;
@@ -184,10 +174,13 @@ void c1101_init(void)
     spi_c1101_dump_registers_to_usb();
     //enable analog temperature sensor on GDO0
     spi_c1101_write_register(SPIC1101_ADDR_IOCFG0, 0x80);
+    //enable RX FIFO interrupt (i.e. GPO1 pulls high if >= FIFOTHR bytes are in RX FIFO)
+    spi_c1101_write_register(SPIC1101_ADDR_IOCFG1, 0);
     // FIFOTHR       RX FIFO and TX FIFO Thresholds
-    spi_c1101_write_register(SPIC1101_ADDR_FIFOTHR, 0x47);
+    // pull GPO high (interrupt) if more than 12 bytes in rx buffer (or less than 53 in tx)
+    spi_c1101_write_register(SPIC1101_ADDR_FIFOTHR, 2);
     // PKTCTRL0      Packet Automation Control
-    spi_c1101_write_register(SPIC1101_ADDR_PKTCTRL0, 0x05);
+    spi_c1101_write_register(SPIC1101_ADDR_PKTCTRL0, 0b0000000010);
     // FSCTRL1       Frequency Synthesizer Control
     spi_c1101_write_register(SPIC1101_ADDR_FSCTRL1, 0x06);
     // FREQn         Frequency Control Words
@@ -298,6 +291,10 @@ char c1101_getStatus(void)
     return sb;
 }
 
+uint8_t c1101_getNumBytesInTXFifo(void)
+{
+    return spi_c1101_read_register(SPIC1101_ADDR_TXBYTES);
+}
 
 void c1101_transmitData(char *buffer, unsigned int len)
 {
@@ -308,23 +305,45 @@ void c1101_transmitData(char *buffer, unsigned int len)
     //configure state machine to automatically go to IDLE, once packet was transmitted
     mcsm1 = (mcsm1 & 0b11111100) | 0b00;
     spi_c1101_write_register(SPIC1101_ADDR_MCSM1, 0x18);
+
+    uint8_t debug_sb[6];
+
     //fill buffer
-    do
-    {
-        num_written = spi_c1101_write_txfifo(buffer, len);
-        buffer += num_written;
-        len -= num_written;
-    } while (num_written > 0);
+    num_written = spi_c1101_write_txfifo(buffer, len);
+    buffer += num_written;
+    len -= num_written;
+
+    usb_rawhid_send((uint8_t*)"TX num written",255);
+    debug_sprint_int16hex(debug_sb, num_written);
+    usb_rawhid_send(debug_sb,255);
+    usb_rawhid_send((uint8_t*)"TX len",255);
+    debug_sprint_int16hex(debug_sb, len);
+    usb_rawhid_send(debug_sb,255);
+
+    c1101_getStatus();
+    usb_rawhid_send((uint8_t*)"TX bytes",255);
+    debug_sprint_int16hex(debug_sb, c1101_getNumBytesInTXFifo());
+    usb_rawhid_send(debug_sb,255);
+
     //start transmitting
     spi_c1101_strobe_command(SPIC1101_ADDR_STX);
     //keep buffer filled
     do
     {
-        num_written = spi_c1101_write_txfifo(buffer, len);
+        num_written = spi_c1101_write_txfifo(buffer,  len );
         buffer += num_written;
         len -= num_written;
-        if (num_written == 0 && len > 0)
-            _delay_ms(1);
+
+        usb_rawhid_send((uint8_t*)"TX2 num written",255);
+        debug_sprint_int16hex(debug_sb, num_written);
+        usb_rawhid_send(debug_sb,255);
+        usb_rawhid_send((uint8_t*)"TX2 len",255);
+        debug_sprint_int16hex(debug_sb, len);
+        usb_rawhid_send(debug_sb,255);
+        c1101_getStatus();
+        usb_rawhid_send((uint8_t*)"TX2 bytes",255);
+        debug_sprint_int16hex(debug_sb, c1101_getNumBytesInTXFifo());
+        usb_rawhid_send(debug_sb,255);
     } while (len > 0);
 }