From 186e9f558ceae20fad066cfa8711243d8effb047 Mon Sep 17 00:00:00 2001
From: Bernhard Tittelbach <xro@realraum.at>
Date: Thu, 12 Jul 2012 18:36:22 +0000
Subject: settings from rfstudio for comparision

git-svn-id: https://svn.spreadspace.org/mur.sat@579 7de4ea59-55d0-425e-a1af-a3118ea81d4c
---
 software/hhd70dongle/c1101lib.c | 44 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 44 insertions(+)

(limited to 'software/hhd70dongle/c1101lib.c')

diff --git a/software/hhd70dongle/c1101lib.c b/software/hhd70dongle/c1101lib.c
index b7ea1c7..077b631 100644
--- a/software/hhd70dongle/c1101lib.c
+++ b/software/hhd70dongle/c1101lib.c
@@ -279,6 +279,50 @@ void c1101_init(void)
     //c1101_setFrequency(1091741,0,15);
 }
 
+//Note for comparision:
+void c1101_init_w_rfstudiosettings1(void)
+{
+//  Sync word qualifier mode = 30/32 sync word bits detected
+//  CRC autoflush = false
+//  Channel spacing = 199.951172
+//  Data format = Normal mode
+//  Data rate = 9.59587
+//  RX filter BW = 58.035714
+//  PA ramping = true
+//  Preamble count = 4
+//  Address config = No address check
+//  Whitening = false
+//  Carrier frequency = 435.124695
+//  Device address = 0
+//  TX power = 10
+//  Manchester enable = false
+//  CRC enable = true
+//  Deviation = 11.901855
+//  Modulation format = GFSK
+//  Base frequency = 435.124695
+//  Modulated = true
+//  Channel number = 0
+//  PA table
+#define PA_TABLE {0x00,0x12,0x0e,0x34,0x60,0xc5,0xc1,0xc0,}
+//
+// Rf settings for CC1101
+//
+    //reset C1101
+    c1101_spi_strobe_command(SPIC1101_ADDR_SRES);
+    _delay_ms(100);
+    //flush FIFOs
+    c1101_spi_strobe_command(SPIC1101_ADDR_SFRX);
+    c1101_spi_strobe_command(SPIC1101_ADDR_SFTX);
+    //enable analog temperature sensor on GDO0
+    c1101_spi_write_register(SPIC1101_ADDR_IOCFG0, 0x80);
+    //enable RX FIFO interrupt (i.e. GPO2 pulls high if >= FIFOTHR bytes are in RX FIFO)
+    c1101_spi_write_register(SPIC1101_ADDR_IOCFG2, 0x41 ); //0x40, 0x42, 0x44, 0x47
+
+    //Values from SmartRFStudio:
+
+}
+
+
 //f_XOSC = 26Mhz
 // freq:            desired_carrier_freq [Hz] *2^16 / f_XOSC
 // freq_offset:     desired frequency offset [Hz] *2^14 / f_XOSC
-- 
cgit v1.2.3