Network Working Group O. Gsenger Internet-Draft March 2007 Expires: September 2, 2007 Anycast stream relaying draft-gsenger-anycast-relay-00 Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on September 2, 2007. Copyright Notice Copyright (C) The IETF Trust (2007). Gsenger Expires September 2, 2007 [Page 1] Internet-Draft Anycast stream relaying March 2007 Abstract The anycast tunneling (anytun) protocol defines a protocol used for communication between unicast clients and anycast servers. It can be used for tunneling information between 2 clients over the servers or in relay mode to transmit data form the client over the servers to a third party not using the protocol and vice versa. Gsenger Expires September 2, 2007 [Page 2] Internet-Draft Anycast stream relaying March 2007 1. Introduction anytun defines a Host Anycast Service as defined in rfc1546. It can be used to build high scalable and redundant tunnel services. It supports both UDP and TCP connections. Additionally to the possibility of establashing an unicast TCP connection over an anycast address as suggested in rfc1546, it supports real anycast TCP connections with state syncronisation and heuristic state forecast. It also has a relay mode, that makes it possible, that only one of the connection endpoints has to use the anytun protocol. This can be used to make connections through Firewalls or behind a NAT Router RFC3068 [1] DTD. Gsenger Expires September 2, 2007 [Page 3] Internet-Draft Anycast stream relaying March 2007 2. Operation modes This section gives an overview of possible operation modes und usage scenarios. Please note, that the protocols used in the figures are only examples and that anytun itself does not care about either transport protocols or encapsulated protocols. Routing and network address translation is not done by anytun. Each implemetation MAY choose it's own way of doing this task (e.g. using functions provided by the operating system). Anytun is used to establish and controll tunnnels, to encapsulate and encrypt data. 2.1. Tunnel modes 2.1.1. Tunneling Mode An example of anytun used in tunnel mode ----------- ----------- | RTP | ---------- | RTP | ----------- -> |server 1| -> ----------- | UDP | ---------- | UDP | ----------- ----------- ----- | IPv6 | ---------- | IPv6 | ----- | | -> ----------- -> |server 2| -> ----------- -> | | ----- | anytun | ---------- | anytun | ----- ##### ----------- ----------- ##### | UDP | ---------- | UDP | client 1 ----------- -> |server 3| -> ----------- client 2 | IPv4 | ---------- | IPv4 | ----------- ----------- | ... | anycast | ... | Figure 1 In tunneling mode the payload of the anytun packet is transmitted from one unicast host to the anycast server. This server makes a routing descision based on the underlying protocol and transmits a new anytun package to one or more clients depending on the routing descition. The server MAY also route the packet to a directly connected network or a service running on the server, but please note, that this is only usefull for anycast host services like DNS and that the services HAVE TO be running on all servers in order to work. Gsenger Expires September 2, 2007 [Page 4] Internet-Draft Anycast stream relaying March 2007 2.1.2. Open tunnel mode An example of anytun used in open tunnel mode ----------- | RTP | ---------- ----------- -> |server 1| -> | UDP | ---------- ----------- ----------- | RTP | ----- | IPv6 | ---------- ----------- ----- | | -> ----------- -> |server 2| -> | UDP* | -> | | ----- | anytun | ---------- ----------- ----- ##### ----------- | IPv6* | ##### | UDP | ---------- ----------- client 1 ----------- -> |server 3| -> | ... | host | IPv4 | ---------- not using ----------- anytun | ... | anycast *changed source address or port Figure 2 In open tunnel mode only one of two clients talking to each other over the servers MUST use the anytun protocol. When a client using the anytun protocol wants to tunnel data, it is building a connection to the anycast servers using the anytun protocol. The anycast servers relay the encapsulated packages directly to the destination without using the anytun protocol. The source address of the datagramm HAS TO be changed to the anycast address of the server. The anytun servers act like a source NAT router, therefor for the destination it saems that it is talking to the client directly. Gsenger Expires September 2, 2007 [Page 5] Internet-Draft Anycast stream relaying March 2007 2.1.3. relay mode An example of anytun used in relay mode ----------- ----- | RTP | ---------- | | -> ----------- -> |server 1| -> ----- | UDP** | ---------- ----------- ##### ----------- | RTP | | IPv6**| ---------- ----------- ----- host ----------- -> |server 2| -> | UDP* | -> | | not using | ... | ---------- ----------- ----- anytun | IPv6* | ##### ---------- ----------- ----------- -> |server 3| | ... | host ----- | anytun | ---------- not using | | -> ----------- anytun ----- | IPv4 | anycast ##### ----------- connection| ... | controller *changed source address or port **changed destination address or port Figure 3 In relay mode the anycast serveres directly repaet the packetes of clients, only the source and destination addresses are changed. The anytun protocol is only used for controll messages, but not fr encapsulation. 2.2. Transport modes Gsenger Expires September 2, 2007 [Page 6] Internet-Draft Anycast stream relaying March 2007 2.2.1. anycast udp mode An example of anytun used with udp transport ----------- ----------- | RTP | ---------- | RTP | ----------- -> |server 1| -> ----------- | UDP | ---------- | UDP | ----------- ----------- ----- | IPv6 | ---------- | IPv6 | ----- | | -> ----------- -> |server 2| -> ----------- -> | | ----- | anytun | ---------- | anytun | ----- ##### ----------- ----------- ##### | UDP | ---------- | UDP | client 1 ----------- -> |server 3| -> ----------- client 2 | IPv4 | ---------- | IPv4 | ----------- ----------- | ... | anycast | ... | Figure 4 In anycast udp mode the data between clients and anycast serveres is carried by udp packets. Packets are routed by the serveres from one client to another. Because udp is stateless no inforamtion has to be syncronised 2.2.2. anycast light udp mode An example of anytun used with udp transport ----------- ----------- | RTP | ---------- | RTP | ----------- -> |server 1| -> ----------- | UDP | ---------- | UDP | ----------- ----------- ----- | IPv6 | ---------- | IPv6 | ----- | | -> ----------- -> |server 2| -> ----------- -> | | ----- | anytun | ---------- | anytun | ----- ##### ----------- ----------- ##### |lightUDP | ---------- |lightUDP | client 1 ----------- -> |server 3| -> ----------- client 2 | IPv4 | ---------- | IPv4 | ----------- ----------- | ... | anycast | ... | Figure 5 The light UDP mode is neerly the same as the normal UDP mode, the Gsenger Expires September 2, 2007 [Page 7] Internet-Draft Anycast stream relaying March 2007 only difference is, that the udp size is set to the udp header lenght and not to the length of the full packet and therefor the checksum is only calculated for the udo header itself. So there is no error correction or detection done on the payload. This can be usefull if realtime data is beeing transimittet or the tunneled protocol does error correction/detection by itself. 2.2.3. unicast tcp with anycast initialisation 2.2.4. full anycast tcp 2.2.4.1. keep alive message request Most NAT routers need a tcp connection to transmit some packets once in while to stay open. In full anycast tcp mode anytun hast to predict the tcp state including the sequence number. Synconisation of the sequence number would be to much overhead, so a keep alive intervall is agreed. This interval is used to calculate the sequemce number. Gsenger Expires September 2, 2007 [Page 8] Internet-Draft Anycast stream relaying March 2007 3. Protocol specification 3.1. Header format 3.2. Protocol field The protocol field defines the payload protocol. ETHER TYPE protocol numerbers are used. http://www.iana.org/assignments/ethernet-numbers Values from 0 to 0000-05DC are not used for DIX ethernet lenght, but are reservered for special purposes. As the definition of transparent ethernet bridging is very unclear 2 special types are added for ethernet frames HEX 0001 Raw Ethernet - both IEEE 802.3 and DIX Etherernet without preamble,SFD, PAD and FCS 0002 Raw Ethernet with FCS further special types MAY be added in the furture. Most important ETHER TYPEs 0800 Internet IP (IPv4) 86DD IPv6 Gsenger Expires September 2, 2007 [Page 9] Internet-Draft Anycast stream relaying March 2007 Appendix A. The appan Gsenger Expires September 2, 2007 [Page 10] Internet-Draft Anycast stream relaying March 2007 4. References [1] Huitema, C., "An Anycast Prefix for 6to4 Relay Routers", RFC 3068, June 2001. Gsenger Expires September 2, 2007 [Page 11] Internet-Draft Anycast stream relaying March 2007 Author's Address Othmar Gsenger Sporgasse 6 Graz 8010 AT Phone: Email: otti@wirdorange.org URI: http://anytun.org/ Gsenger Expires September 2, 2007 [Page 12] Internet-Draft Anycast stream relaying March 2007 Full Copyright Statement Copyright (C) The IETF Trust (2007). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Acknowledgment Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA). Gsenger Expires September 2, 2007 [Page 13]