From 88f272bac7af8c021f0bd272dbc841441279f5c7 Mon Sep 17 00:00:00 2001 From: Christian Pointner Date: Thu, 11 Feb 2010 10:57:11 +0000 Subject: cleaned up manpages --- doc/anytun-config.8 | 48 ++++++++--------- doc/anytun-config.8.txt | 45 ++++++++-------- doc/anytun-controld.8 | 30 +++++------ doc/anytun-controld.8.txt | 27 +++++----- doc/anytun-showtables.8 | 4 +- doc/anytun-showtables.8.txt | 1 + doc/anytun.8 | 122 ++++++++++++++++++++++---------------------- doc/anytun.8.txt | 107 +++++++++++++++++++------------------- 8 files changed, 194 insertions(+), 190 deletions(-) (limited to 'doc') diff --git a/doc/anytun-config.8 b/doc/anytun-config.8 index 4a349c3..5facb41 100644 --- a/doc/anytun-config.8 +++ b/doc/anytun-config.8 @@ -2,12 +2,12 @@ .\" Title: anytun-config .\" Author: [see the "AUTHORS" section] .\" Generator: DocBook XSL Stylesheets v1.75.1 -.\" Date: 01/15/2010 +.\" Date: 02/11/2010 .\" Manual: anytun-config user manual .\" Source: anytun trunk .\" Language: English .\" -.TH "ANYTUN\-CONFIG" "8" "01/15/2010" "anytun trunk" "anytun-config user manual" +.TH "ANYTUN\-CONFIG" "8" "02/11/2010" "anytun trunk" "anytun-config user manual" .\" ----------------------------------------------------------------- .\" * set default formatting .\" ----------------------------------------------------------------- @@ -45,32 +45,32 @@ anytun-config \- anycast tunneling configuration utility \fBanytun\-config\fR writes routing/connection table entries, that can be read by \fBanytun\-controld\fR\&. .SH "OPTIONS" .PP -\fB\-L, \-\-log :[,[,[\&.\&.]]]\fR +\fB\-L, \-\-log \fR\fB\fI:[,[,[\&.\&.]]]\fR\fR .RS 4 add log target to logging system\&. This can be invoked several times in order to log to different targets at the same time\&. Every target hast its own log level which is a number between 0 and 5\&. Where 0 means disabling log and 5 means debug messages are enabled\&. The file target can be used more the once with different levels\&. If no target is provided at the command line a single target with the config -\fBsyslog:3,anytun\-config,daemon\fR +\fIsyslog:3,anytun\-config,daemon\fR is added\&. The following targets are supported: .PP -\fBsyslog\fR +\fIsyslog\fR .RS 4 log to syslog daemon, parameters [,[,]] .RE .PP -\fBfile\fR +\fIfile\fR .RS 4 log to file, parameters [,] .RE .PP -\fBstdout\fR +\fIstdout\fR .RS 4 log to standard output, parameters .RE .PP -\fBstderr\fR +\fIstderr\fR .RS 4 log to standard error, parameters .RE @@ -83,16 +83,16 @@ This option instructs to run in debug mode\&. It implicits \fB\-D\fR (don\(cqt daemonize) and adds a log target with the configuration -\fBstdout:5\fR +\fIstdout:5\fR (logging with maximum level)\&. In future releases there might be additional output when this option is supplied\&. .RE .PP -\fB\-r, \-\-remote\-host \fR +\fB\-r, \-\-remote\-host \fR\fB\fI\fR\fR .RS 4 This option can be used to specify the remote tunnel endpoint\&. In case of anycast tunnel endpoints, the anycast IP address has to be used\&. If you do not specify an address, it is automatically determined after receiving the first data packet\&. .RE .PP -\fB\-o, \-\-remote\-port \fR +\fB\-o, \-\-remote\-port \fR\fB\fI\fR\fR .RS 4 The UDP port used for payload data by the remote host (specified with \-p on the remote host)\&. If you do not specify a port, it is automatically determined after receiving the first data packet\&. .RE @@ -107,24 +107,24 @@ Resolv to IPv4 addresses only\&. The default is to resolv both IPv4 and IPv6 add Resolv to IPv6 addresses only\&. The default is to resolv both IPv4 and IPv6 addresses\&. .RE .PP -\fB\-R, \-\-route /\fR +\fB\-R, \-\-route \fR\fB\fI/\fR\fR .RS 4 add a route to connection\&. This can be invoked several times\&. .RE .PP -\fB\-m, \-\-mux \fR +\fB\-m, \-\-mux \fR\fB\fI\fR\fR .RS 4 the multiplex id to use\&. default: 0 .RE .PP -\fB\-w, \-\-window\-size \fR +\fB\-w, \-\-window\-size \fR\fB\fI\fR\fR .RS 4 seqence window size Sometimes, packets arrive out of order on the receiver side\&. This option defines the size of a list of received packets\' sequence numbers\&. If, according to this list, a received packet has been previously received or has been transmitted in the past, and is therefore not in the list anymore, this is interpreted as a replay attack and the packet is dropped\&. A value of 0 deactivates this list and, as a consequence, the replay protection employed by filtering packets according to their secuence number\&. By default the sequence window is disabled and therefore a window size of 0 is used\&. .RE .PP -\fB\-k, \-\-kd\(emprf \fR +\fB\-k, \-\-kd\(emprf \fR\fB\fI\fR\fR .RS 4 key derivation pseudo random function @@ -132,33 +132,33 @@ The pseudo random function which is used for calculating the session keys and se Possible values: .PP -\fBnull\fR +\fInull\fR .RS 4 no random function, keys and salt are set to 0\&.\&.00 .RE .PP -\fBaes\-ctr\fR +\fIaes\-ctr\fR .RS 4 AES in counter mode with 128 Bits, default value .RE .PP -\fBaes\-ctr\-128\fR +\fIaes\-ctr\-128\fR .RS 4 AES in counter mode with 128 Bits .RE .PP -\fBaes\-ctr\-192\fR +\fIaes\-ctr\-192\fR .RS 4 AES in counter mode with 192 Bits .RE .PP -\fBaes\-ctr\-256\fR +\fIaes\-ctr\-256\fR .RS 4 AES in counter mode with 256 Bits .RE .RE .PP -\fB\-e, \-\-role \fR +\fB\-e, \-\-role \fR\fB\fI\fR\fR .RS 4 SATP uses different session keys for inbound and outbound traffic\&. The role parameter is used to determine which keys to use for outbound or inbound packets\&. On both sides of a vpn connection different roles have to be used\&. Possible values are \fBleft\fR @@ -179,7 +179,7 @@ as a replacement for is used\&. .RE .PP -\fB\-E, \-\-passphrase \fR +\fB\-E, \-\-passphrase \fR\fB\fI\fR\fR .RS 4 This passphrase is used to generate the master key and master salt\&. For the master key the last n bits of the SHA256 digest of the passphrase (where n is the length of the master key in bits) is used\&. The master salt gets generated with the SHA1 digest\&. You may force a specific key and or salt by using \fB\-\-key\fR @@ -187,14 +187,14 @@ and \fB\-\-salt\fR\&. .RE .PP -\fB\-K, \-\-key \fR +\fB\-K, \-\-key \fR\fB\fI\fR\fR .RS 4 master key to use for key derivation Master key in hexadecimal notation, e\&.g\&. 01a2b3c4d5e6f708a9b0cadbecfd0fa1, with a mandatory length of 32, 48 or 64 characters (128, 192 or 256 bits)\&. .RE .PP -\fB\-A, \-\-salt \fR +\fB\-A, \-\-salt \fR\fB\fI\fR\fR .RS 4 master salt to use for key derivation diff --git a/doc/anytun-config.8.txt b/doc/anytun-config.8.txt index 89be356..1aebf9a 100644 --- a/doc/anytun-config.8.txt +++ b/doc/anytun-config.8.txt @@ -3,6 +3,7 @@ anytun-config(8) NAME ---- + anytun-config - anycast tunneling configuration utility SYNOPSIS @@ -35,35 +36,35 @@ DESCRIPTION OPTIONS ------- -*-L, --log :[,[,[..]]]*:: +*-L, --log ':[,[,[..]]]'*:: add log target to logging system. This can be invoked several times in order to log to different targets at the same time. Every target hast its own log level which is a number between 0 and 5. Where 0 means disabling log and 5 means debug messages are enabled. + The file target can be used more the once with different levels. If no target is provided at the command line a single target with the - config *syslog:3,anytun-config,daemon* is added. + + config 'syslog:3,anytun-config,daemon' is added. + The following targets are supported: - *syslog*;; log to syslog daemon, parameters [,[,]] - *file*;; log to file, parameters [,] - *stdout*;; log to standard output, parameters - *stderr*;; log to standard error, parameters + 'syslog';; log to syslog daemon, parameters [,[,]] + 'file';; log to file, parameters [,] + 'stdout';; log to standard output, parameters + 'stderr';; log to standard error, parameters *-U, --debug*:: This option instructs *Anytun* to run in debug mode. It implicits *-D* (don't daemonize) and adds a log target with the configuration - *stdout:5* (logging with maximum level). In future releases there might + 'stdout:5' (logging with maximum level). In future releases there might be additional output when this option is supplied. -*-r, --remote-host *:: +*-r, --remote-host ''*:: This option can be used to specify the remote tunnel endpoint. In case of anycast tunnel endpoints, the anycast IP address has to be used. If you do not specify an address, it is automatically determined after receiving the first data packet. -*-o, --remote-port *:: +*-o, --remote-port ''*:: The UDP port used for payload data by the remote host (specified with -p on the remote host). If you do not specify a port, it is automatically determined after receiving @@ -77,13 +78,13 @@ OPTIONS Resolv to IPv6 addresses only. The default is to resolv both IPv4 and IPv6 addresses. -*-R, --route /*:: +*-R, --route '/'*:: add a route to connection. This can be invoked several times. -*-m, --mux *:: +*-m, --mux ''*:: the multiplex id to use. default: 0 -*-w, --window-size *:: +*-w, --window-size ''*:: seqence window size + Sometimes, packets arrive out of order on the receiver side. This option defines the size of a list of received @@ -97,19 +98,19 @@ OPTIONS By default the sequence window is disabled and therefore a window size of 0 is used. -*-k, --kd--prf *:: +*-k, --kd--prf ''*:: key derivation pseudo random function + The pseudo random function which is used for calculating the session keys and session salt. + Possible values: - *null*;; no random function, keys and salt are set to 0..00 - *aes-ctr*;; AES in counter mode with 128 Bits, default value - *aes-ctr-128*;; AES in counter mode with 128 Bits - *aes-ctr-192*;; AES in counter mode with 192 Bits - *aes-ctr-256*;; AES in counter mode with 256 Bits + 'null';; no random function, keys and salt are set to 0..00 + 'aes-ctr';; AES in counter mode with 128 Bits, default value + 'aes-ctr-128';; AES in counter mode with 128 Bits + 'aes-ctr-192';; AES in counter mode with 192 Bits + 'aes-ctr-256';; AES in counter mode with 256 Bits -*-e, --role *:: +*-e, --role ''*:: SATP uses different session keys for inbound and outbound traffic. The role parameter is used to determine which keys to use for outbound or inbound packets. On both sides of a vpn connection different roles have @@ -117,20 +118,20 @@ OPTIONS *alice* or *server* as a replacement for *left* and *bob* or *client* as a replacement for *right*. By default *left* is used. -*-E, --passphrase *:: +*-E, --passphrase ''*:: This passphrase is used to generate the master key and master salt. For the master key the last n bits of the SHA256 digest of the passphrase (where n is the length of the master key in bits) is used. The master salt gets generated with the SHA1 digest. You may force a specific key and or salt by using *--key* and *--salt*. -*-K, --key *:: +*-K, --key ''*:: master key to use for key derivation + Master key in hexadecimal notation, e.g. 01a2b3c4d5e6f708a9b0cadbecfd0fa1, with a mandatory length of 32, 48 or 64 characters (128, 192 or 256 bits). -*-A, --salt *:: +*-A, --salt ''*:: master salt to use for key derivation + Master salt in hexadecimal notation, e.g. 01a2b3c4d5e6f708a9b0cadbecfd, with a mandatory length diff --git a/doc/anytun-controld.8 b/doc/anytun-controld.8 index 6151363..cfcdf41 100644 --- a/doc/anytun-controld.8 +++ b/doc/anytun-controld.8 @@ -2,12 +2,12 @@ .\" Title: anytun-controld .\" Author: [see the "AUTHORS" section] .\" Generator: DocBook XSL Stylesheets v1.75.1 -.\" Date: 01/15/2010 +.\" Date: 02/11/2010 .\" Manual: anytun-controld user manual .\" Source: anytun trunk .\" Language: English .\" -.TH "ANYTUN\-CONTROLD" "8" "01/15/2010" "anytun trunk" "anytun-controld user manual" +.TH "ANYTUN\-CONTROLD" "8" "02/11/2010" "anytun trunk" "anytun-controld user manual" .\" ----------------------------------------------------------------- .\" * set default formatting .\" ----------------------------------------------------------------- @@ -47,56 +47,56 @@ This option instructs to run in foreground instead of becoming a daemon which is the default\&. .RE .PP -\fB\-u, \-\-username \fR +\fB\-u, \-\-username \fR\fB\fI\fR\fR .RS 4 run as this user\&. If no group is specified (\fB\-g\fR) the default group of the user is used\&. The default is to not drop privileges\&. .RE .PP -\fB\-g, \-\-groupname \fR +\fB\-g, \-\-groupname \fR\fB\fI\fR\fR .RS 4 run as this group\&. If no username is specified (\fB\-u\fR) this gets ignored\&. The default is to not drop privileges\&. .RE .PP -\fB\-C, \-\-chroot \fR +\fB\-C, \-\-chroot \fR\fB\fI\fR\fR .RS 4 Instruct \fBanytun\-controld\fR to run in a chroot jail\&. The default is to not run in chroot\&. .RE .PP -\fB\-P, \-\-write\-pid \fR +\fB\-P, \-\-write\-pid \fR\fB\fI\fR\fR .RS 4 Instruct \fBanytun\-controld\fR to write it\(cqs pid to this file\&. The default is to not create a pid file\&. .RE .PP -\fB\-L, \-\-log :[,[,[\&.\&.]]]\fR +\fB\-L, \-\-log \fR\fB\fI:[,[,[\&.\&.]]]\fR\fR .RS 4 add log target to logging system\&. This can be invoked several times in order to log to different targets at the same time\&. Every target hast its own log level which is a number between 0 and 5\&. Where 0 means disabling log and 5 means debug messages are enabled\&. The file target can be used more the once with different levels\&. If no target is provided at the command line a single target with the config -\fBsyslog:3,anytun\-controld,daemon\fR +\fIsyslog:3,anytun\-controld,daemon\fR is added\&. The following targets are supported: .PP -\fBsyslog\fR +\fIsyslog\fR .RS 4 log to syslog daemon, parameters [,[,]] .RE .PP -\fBfile\fR +\fIfile\fR .RS 4 log to file, parameters [,] .RE .PP -\fBstdout\fR +\fIstdout\fR .RS 4 log to standard output, parameters .RE .PP -\fBstderr\fR +\fIstderr\fR .RS 4 log to standard error, parameters .RE @@ -109,16 +109,16 @@ This option instructs to run in debug mode\&. It implicits \fB\-D\fR (don\(cqt daemonize) and adds a log target with the configuration -\fBstdout:5\fR +\fIstdout:5\fR (logging with maximum level)\&. In future releases there might be additional output when this option is supplied\&. .RE .PP -\fB\-f, \-\-file \fR +\fB\-f, \-\-file \fR\fB\fI\fR\fR .RS 4 The path to the file which holds the sync information\&. .RE .PP -\fB\-X, \-\-control\-host [:]\fR +\fB\-X, \-\-control\-host \fR\fB\fI[:]\fR\fR .RS 4 fetch the config from this host\&. The default is not to use a control host and therefore this is empty\&. Mind that the port can be omitted in which case port 2323 is used\&. If you want to specify an ipv6 address and a port you have to use [ and ] to separate the address from the port, eg\&.: [::1]:1234\&. If you want to use the default port [ and ] can be omitted\&. .RE diff --git a/doc/anytun-controld.8.txt b/doc/anytun-controld.8.txt index 413fa40..6c7a3d8 100644 --- a/doc/anytun-controld.8.txt +++ b/doc/anytun-controld.8.txt @@ -3,6 +3,7 @@ anytun-controld(8) NAME ---- + anytun-controld - anycast tunneling control daemon SYNOPSIS @@ -34,47 +35,47 @@ OPTIONS This option instructs *anytun-controld* to run in foreground instead of becoming a daemon which is the default. -*-u, --username *:: +*-u, --username ''*:: run as this user. If no group is specified (*-g*) the default group of the user is used. The default is to not drop privileges. -*-g, --groupname *:: +*-g, --groupname ''*:: run as this group. If no username is specified (*-u*) this gets ignored. The default is to not drop privileges. -*-C, --chroot *:: +*-C, --chroot ''*:: Instruct *anytun-controld* to run in a chroot jail. The default is to not run in chroot. -*-P, --write-pid *:: +*-P, --write-pid ''*:: Instruct *anytun-controld* to write it's pid to this file. The default is to not create a pid file. -*-L, --log :[,[,[..]]]*:: +*-L, --log ':[,[,[..]]]'*:: add log target to logging system. This can be invoked several times in order to log to different targets at the same time. Every target hast its own log level which is a number between 0 and 5. Where 0 means disabling log and 5 means debug messages are enabled. + The file target can be used more the once with different levels. If no target is provided at the command line a single target with the - config *syslog:3,anytun-controld,daemon* is added. + + config 'syslog:3,anytun-controld,daemon' is added. + The following targets are supported: - *syslog*;; log to syslog daemon, parameters [,[,]] - *file*;; log to file, parameters [,] - *stdout*;; log to standard output, parameters - *stderr*;; log to standard error, parameters + 'syslog';; log to syslog daemon, parameters [,[,]] + 'file';; log to file, parameters [,] + 'stdout';; log to standard output, parameters + 'stderr';; log to standard error, parameters *-U, --debug*:: This option instructs *Anytun* to run in debug mode. It implicits *-D* (don't daemonize) and adds a log target with the configuration - *stdout:5* (logging with maximum level). In future releases there might + 'stdout:5' (logging with maximum level). In future releases there might be additional output when this option is supplied. -*-f, --file *:: +*-f, --file ''*:: The path to the file which holds the sync information. -*-X, --control-host [:]*:: +*-X, --control-host '[:]'*:: fetch the config from this host. The default is not to use a control host and therefore this is empty. Mind that the port can be omitted in which case port 2323 is used. If you want to specify an diff --git a/doc/anytun-showtables.8 b/doc/anytun-showtables.8 index a1230e4..4d91bc0 100644 --- a/doc/anytun-showtables.8 +++ b/doc/anytun-showtables.8 @@ -2,12 +2,12 @@ .\" Title: anytun-showtables .\" Author: [see the "AUTHORS" section] .\" Generator: DocBook XSL Stylesheets v1.75.1 -.\" Date: 12/22/2009 +.\" Date: 02/11/2010 .\" Manual: anytun-showtables user manual .\" Source: anytun trunk .\" Language: English .\" -.TH "ANYTUN\-SHOWTABLES" "8" "12/22/2009" "anytun trunk" "anytun-showtables user manual" +.TH "ANYTUN\-SHOWTABLES" "8" "02/11/2010" "anytun trunk" "anytun-showtables user manual" .\" ----------------------------------------------------------------- .\" * set default formatting .\" ----------------------------------------------------------------- diff --git a/doc/anytun-showtables.8.txt b/doc/anytun-showtables.8.txt index 3a1fa8d..13070a4 100644 --- a/doc/anytun-showtables.8.txt +++ b/doc/anytun-showtables.8.txt @@ -3,6 +3,7 @@ anytun-showtables(8) NAME ---- + anytun-showtables - anycast tunneling routing table visualization utility SYNOPSIS diff --git a/doc/anytun.8 b/doc/anytun.8 index 1f5b6c9..3b6aa79 100644 --- a/doc/anytun.8 +++ b/doc/anytun.8 @@ -2,12 +2,12 @@ .\" Title: anytun .\" Author: [see the "AUTHORS" section] .\" Generator: DocBook XSL Stylesheets v1.75.1 -.\" Date: 01/15/2010 +.\" Date: 02/11/2010 .\" Manual: anytun user manual .\" Source: anytun trunk .\" Language: English .\" -.TH "ANYTUN" "8" "01/15/2010" "anytun trunk" "anytun user manual" +.TH "ANYTUN" "8" "02/11/2010" "anytun trunk" "anytun user manual" .\" ----------------------------------------------------------------- .\" * set default formatting .\" ----------------------------------------------------------------- @@ -73,56 +73,56 @@ This option instructs to run in foreground instead of becoming a daemon which is the default\&. .RE .PP -\fB\-u, \-\-username \fR +\fB\-u, \-\-username \fR\fB\fI\fR\fR .RS 4 run as this user\&. If no group is specified (\fB\-g\fR) the default group of the user is used\&. The default is to not drop privileges\&. .RE .PP -\fB\-g, \-\-groupname \fR +\fB\-g, \-\-groupname \fR\fB\fI\fR\fR .RS 4 run as this group\&. If no username is specified (\fB\-u\fR) this gets ignored\&. The default is to not drop privileges\&. .RE .PP -\fB\-C, \-\-chroot \fR +\fB\-C, \-\-chroot \fR\fB\fI\fR\fR .RS 4 Instruct \fBAnytun\fR to run in a chroot jail\&. The default is to not run in chroot\&. .RE .PP -\fB\-P, \-\-write\-pid \fR +\fB\-P, \-\-write\-pid \fR\fB\fI\fR\fR .RS 4 Instruct \fBAnytun\fR to write it\(cqs pid to this file\&. The default is to not create a pid file\&. .RE .PP -\fB\-L, \-\-log :[,[,[\&.\&.]]]\fR +\fB\-L, \-\-log \fR\fB\fI:[,[,[\&.\&.]]]\fR\fR .RS 4 add log target to logging system\&. This can be invoked several times in order to log to different targets at the same time\&. Every target hast its own log level which is a number between 0 and 5\&. Where 0 means disabling log and 5 means debug messages are enabled\&. The file target can be used more the once with different levels\&. If no target is provided at the command line a single target with the config -\fBsyslog:3,anytun,daemon\fR +\fIsyslog:3,anytun,daemon\fR is added\&. The following targets are supported: .PP -\fBsyslog\fR +\fIsyslog\fR .RS 4 log to syslog daemon, parameters [,[,]] .RE .PP -\fBfile\fR +\fIfile\fR .RS 4 log to file, parameters [,] .RE .PP -\fBstdout\fR +\fIstdout\fR .RS 4 log to standard output, parameters .RE .PP -\fBstderr\fR +\fIstderr\fR .RS 4 log to standard error, parameters .RE @@ -135,26 +135,26 @@ This option instructs to run in debug mode\&. It implicits \fB\-D\fR (don\(cqt daemonize) and adds a log target with the configuration -\fBstdout:5\fR +\fIstdout:5\fR (logging with maximum level)\&. In future releases there might be additional output when this option is supplied\&. .RE .PP -\fB\-i, \-\-interface \fR +\fB\-i, \-\-interface \fR\fB\fI\fR\fR .RS 4 This IP address is used as the sender address for outgoing packets\&. In case of anycast tunnel endpoints, the anycast IP has to be used\&. In case of unicast endpoints, the address is usually derived correctly from the routing table\&. The default is to not use a special inteface and just bind on all interfaces\&. .RE .PP -\fB\-p, \-\-port \fR +\fB\-p, \-\-port \fR\fB\fI\fR\fR .RS 4 The local UDP port that is used to send and receive the payload data\&. The two tunnel endpoints can use different ports\&. If a tunnel endpoint consists of multiple anycast hosts, all hosts have to use the same port\&. default: 4444 .RE .PP -\fB\-r, \-\-remote\-host \fR +\fB\-r, \-\-remote\-host \fR\fB\fI\fR\fR .RS 4 This option can be used to specify the remote tunnel endpoint\&. In case of anycast tunnel endpoints, the anycast IP address has to be used\&. If you do not specify an address, it is automatically determined after receiving the first data packet\&. .RE .PP -\fB\-o, \-\-remote\-port \fR +\fB\-o, \-\-remote\-port \fR\fB\fI\fR\fR .RS 4 The UDP port used for payload data by the remote host (specified with \-p on the remote host)\&. If you do not specify a port, it is automatically determined after receiving the first data packet\&. .RE @@ -169,7 +169,7 @@ Resolv to IPv4 addresses only\&. The default is to resolv both IPv4 and IPv6 add Resolv to IPv6 addresses only\&. The default is to resolv both IPv4 and IPv6 addresses\&. .RE .PP -\fB\-I, \-\-sync\-interface \fR +\fB\-I, \-\-sync\-interface \fR\fB\fI\fR\fR .RS 4 local unicast(sync) ip address to bind to @@ -177,7 +177,7 @@ This option is only needed for tunnel endpoints consisting of multiple anycast h \fB\-\-sync\-port\fR\&. .RE .PP -\fB\-S, \-\-sync\-port \fR +\fB\-S, \-\-sync\-port \fR\fB\fI\fR\fR .RS 4 local unicast(sync) port to bind to @@ -186,77 +186,77 @@ This option is only needed for tunnel endpoints consisting of multiple anycast h It is possible to obtain a list of active connections by telnetting into this port\&. This port is read\-only and unprotected by default\&. It is advised to protect this port using firewall rules and, eventually, IPsec\&. .RE .PP -\fB\-M, \-\-sync\-hosts [:],[[:][\&...]]\fR +\fB\-M, \-\-sync\-hosts \fR\fB\fI[:],[[:][\&...]]\fR\fR .RS 4 remote hosts to sync with This option is only needed for tunnel endpoints consisting of multiple anycast hosts\&. Here, one has to specify all unicast IP addresses of all other anycast hosts that comprise the anycast tunnel endpoint\&. By default synchronisation is disabled and therefore this is empty\&. Mind that the port can be omitted in which case port 2323 is used\&. If you want to specify an ipv6 address and a port you have to use [ and ] to separate the address from the port, eg\&.: [::1]:1234\&. If you want to use the default port [ and ] can be omitted\&. .RE .PP -\fB\-X, \-\-control\-host [:]\fR +\fB\-X, \-\-control\-host \fR\fB\fI[:]\fR\fR .RS 4 fetch the config from this host\&. The default is not to use a control host and therefore this is empty\&. Mind that the port can be omitted in which case port 2323 is used\&. If you want to specify an ipv6 address and a port you have to use [ and ] to separate the address from the port, eg\&.: [::1]:1234\&. If you want to use the default port [ and ] can be omitted\&. .RE .PP -\fB\-d, \-\-dev \fR +\fB\-d, \-\-dev \fR\fB\fI\fR\fR .RS 4 device name By default, tapN is used for Ethernet tunnel interfaces, and tunN for IP tunnels, respectively\&. This option can be used to manually override these defaults\&. .RE .PP -\fB\-t, \-\-type \fR +\fB\-t, \-\-type \fR\fB\fI\fR\fR .RS 4 device type Type of the tunnels to create\&. Use tap for Ethernet tunnels, tun for IP tunnels\&. .RE .PP -\fB\-n, \-\-ifconfig /\fR +\fB\-n, \-\-ifconfig \fR\fB\fI/\fR\fR .RS 4 The local IP address and prefix length\&. The remote tunnel endpoint has to use a different IP address in the same subnet\&. .PP -\fB\fR +\fI\fR .RS 4 the local IP address for the tun/tap device .RE .PP -\fB\fR +\fI\fR .RS 4 the prefix length of the network .RE .RE .PP -\fB\-x, \-\-post\-up\-script