From 88f272bac7af8c021f0bd272dbc841441279f5c7 Mon Sep 17 00:00:00 2001 From: Christian Pointner Date: Thu, 11 Feb 2010 10:57:11 +0000 Subject: cleaned up manpages --- doc/anytun-config.8 | 48 ++++++++++++++++++++++++------------------------ 1 file changed, 24 insertions(+), 24 deletions(-) (limited to 'doc/anytun-config.8') diff --git a/doc/anytun-config.8 b/doc/anytun-config.8 index 4a349c3..5facb41 100644 --- a/doc/anytun-config.8 +++ b/doc/anytun-config.8 @@ -2,12 +2,12 @@ .\" Title: anytun-config .\" Author: [see the "AUTHORS" section] .\" Generator: DocBook XSL Stylesheets v1.75.1 -.\" Date: 01/15/2010 +.\" Date: 02/11/2010 .\" Manual: anytun-config user manual .\" Source: anytun trunk .\" Language: English .\" -.TH "ANYTUN\-CONFIG" "8" "01/15/2010" "anytun trunk" "anytun-config user manual" +.TH "ANYTUN\-CONFIG" "8" "02/11/2010" "anytun trunk" "anytun-config user manual" .\" ----------------------------------------------------------------- .\" * set default formatting .\" ----------------------------------------------------------------- @@ -45,32 +45,32 @@ anytun-config \- anycast tunneling configuration utility \fBanytun\-config\fR writes routing/connection table entries, that can be read by \fBanytun\-controld\fR\&. .SH "OPTIONS" .PP -\fB\-L, \-\-log :[,[,[\&.\&.]]]\fR +\fB\-L, \-\-log \fR\fB\fI:[,[,[\&.\&.]]]\fR\fR .RS 4 add log target to logging system\&. This can be invoked several times in order to log to different targets at the same time\&. Every target hast its own log level which is a number between 0 and 5\&. Where 0 means disabling log and 5 means debug messages are enabled\&. The file target can be used more the once with different levels\&. If no target is provided at the command line a single target with the config -\fBsyslog:3,anytun\-config,daemon\fR +\fIsyslog:3,anytun\-config,daemon\fR is added\&. The following targets are supported: .PP -\fBsyslog\fR +\fIsyslog\fR .RS 4 log to syslog daemon, parameters [,[,]] .RE .PP -\fBfile\fR +\fIfile\fR .RS 4 log to file, parameters [,] .RE .PP -\fBstdout\fR +\fIstdout\fR .RS 4 log to standard output, parameters .RE .PP -\fBstderr\fR +\fIstderr\fR .RS 4 log to standard error, parameters .RE @@ -83,16 +83,16 @@ This option instructs to run in debug mode\&. It implicits \fB\-D\fR (don\(cqt daemonize) and adds a log target with the configuration -\fBstdout:5\fR +\fIstdout:5\fR (logging with maximum level)\&. In future releases there might be additional output when this option is supplied\&. .RE .PP -\fB\-r, \-\-remote\-host \fR +\fB\-r, \-\-remote\-host \fR\fB\fI\fR\fR .RS 4 This option can be used to specify the remote tunnel endpoint\&. In case of anycast tunnel endpoints, the anycast IP address has to be used\&. If you do not specify an address, it is automatically determined after receiving the first data packet\&. .RE .PP -\fB\-o, \-\-remote\-port \fR +\fB\-o, \-\-remote\-port \fR\fB\fI\fR\fR .RS 4 The UDP port used for payload data by the remote host (specified with \-p on the remote host)\&. If you do not specify a port, it is automatically determined after receiving the first data packet\&. .RE @@ -107,24 +107,24 @@ Resolv to IPv4 addresses only\&. The default is to resolv both IPv4 and IPv6 add Resolv to IPv6 addresses only\&. The default is to resolv both IPv4 and IPv6 addresses\&. .RE .PP -\fB\-R, \-\-route /\fR +\fB\-R, \-\-route \fR\fB\fI/\fR\fR .RS 4 add a route to connection\&. This can be invoked several times\&. .RE .PP -\fB\-m, \-\-mux \fR +\fB\-m, \-\-mux \fR\fB\fI\fR\fR .RS 4 the multiplex id to use\&. default: 0 .RE .PP -\fB\-w, \-\-window\-size \fR +\fB\-w, \-\-window\-size \fR\fB\fI\fR\fR .RS 4 seqence window size Sometimes, packets arrive out of order on the receiver side\&. This option defines the size of a list of received packets\' sequence numbers\&. If, according to this list, a received packet has been previously received or has been transmitted in the past, and is therefore not in the list anymore, this is interpreted as a replay attack and the packet is dropped\&. A value of 0 deactivates this list and, as a consequence, the replay protection employed by filtering packets according to their secuence number\&. By default the sequence window is disabled and therefore a window size of 0 is used\&. .RE .PP -\fB\-k, \-\-kd\(emprf \fR +\fB\-k, \-\-kd\(emprf \fR\fB\fI\fR\fR .RS 4 key derivation pseudo random function @@ -132,33 +132,33 @@ The pseudo random function which is used for calculating the session keys and se Possible values: .PP -\fBnull\fR +\fInull\fR .RS 4 no random function, keys and salt are set to 0\&.\&.00 .RE .PP -\fBaes\-ctr\fR +\fIaes\-ctr\fR .RS 4 AES in counter mode with 128 Bits, default value .RE .PP -\fBaes\-ctr\-128\fR +\fIaes\-ctr\-128\fR .RS 4 AES in counter mode with 128 Bits .RE .PP -\fBaes\-ctr\-192\fR +\fIaes\-ctr\-192\fR .RS 4 AES in counter mode with 192 Bits .RE .PP -\fBaes\-ctr\-256\fR +\fIaes\-ctr\-256\fR .RS 4 AES in counter mode with 256 Bits .RE .RE .PP -\fB\-e, \-\-role \fR +\fB\-e, \-\-role \fR\fB\fI\fR\fR .RS 4 SATP uses different session keys for inbound and outbound traffic\&. The role parameter is used to determine which keys to use for outbound or inbound packets\&. On both sides of a vpn connection different roles have to be used\&. Possible values are \fBleft\fR @@ -179,7 +179,7 @@ as a replacement for is used\&. .RE .PP -\fB\-E, \-\-passphrase \fR +\fB\-E, \-\-passphrase \fR\fB\fI\fR\fR .RS 4 This passphrase is used to generate the master key and master salt\&. For the master key the last n bits of the SHA256 digest of the passphrase (where n is the length of the master key in bits) is used\&. The master salt gets generated with the SHA1 digest\&. You may force a specific key and or salt by using \fB\-\-key\fR @@ -187,14 +187,14 @@ and \fB\-\-salt\fR\&. .RE .PP -\fB\-K, \-\-key \fR +\fB\-K, \-\-key \fR\fB\fI\fR\fR .RS 4 master key to use for key derivation Master key in hexadecimal notation, e\&.g\&. 01a2b3c4d5e6f708a9b0cadbecfd0fa1, with a mandatory length of 32, 48 or 64 characters (128, 192 or 256 bits)\&. .RE .PP -\fB\-A, \-\-salt \fR +\fB\-A, \-\-salt \fR\fB\fI\fR\fR .RS 4 master salt to use for key derivation -- cgit v1.2.3